Name: Fujian Monel 400 Double End Stud Material: Monel 400 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: Resistant to hydrofluoric acidQS Fastener: Monel 400 Double End Stud
Name: Inconel 625 Double End Stud Material: Inconel 625 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 625 Double End Stud
Name: Xiamen Inconel 600 High Strength Fastener Material: Inconel 600 Standard: ASME Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 600 High Strength Fastener
Name: Inconel 600 Stud Bolt Putian Material: Inconel 600 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 600 Stud Bolt
HUS4-CR screw anchor
Anchor size:6-10mm
Anchor length:40-105mm
Material, corrosion:Stainless steel, A4
Head configuration:Countersunk
Approvals / test reports:ETA, Fire
Base materials:Concrete (aerated), Concrete (cracked)
Reusable (and removable):Not possible
Cleaning procedures；Manual cleaning, Non-cleaning
PROFIS software：Yes
1. HUS4-CR screw anchor Product Overview – HIT-MM PLUS Injection Mortar
HIT-MM PLUS Injection Mortar installs medium-duty anchors in solid, hollow or concrete substrates without approvals.
(1) Compatible with manual, cordless and pneumatic guns
(2) HIT-SC sleeves save mortar and fit any cavity
(3) Rapid cure—ready in minutes overhead or vertical
(4) Styrene-free and service-ready from –40 °C to +50 °C
2. HUS4-CR screw anchor Technical Parameters
Parameter | Specification | Notes |
Cartridge size | 330 ml / 500 ml | Standard twin-cartridge |
Base materials | Solid brick, hollow brick, concrete (uncracked) | Dry or wet |
Storage temp | +5 °C to +25 °C | 18-month shelf life |
Service temp | –40 °C to +50 °C | Long-term +24 °C |
Installation temp | +5 °C to +40 °C | Working time 5 min at 20 °C |
3. HUS4-CR screw anchor Performance Data
Rod size | Embedment | Tension Nrec* | Shear Vrec* |
M8 | 60 mm | 1.2 kN | 1.8 kN |
M10 | 70 mm | 2.0 kN | 3.0 kN |
M12 | 90 mm | 3.2 kN | 4.5 kN |
*Solid clay brick Mz 12, fbal ≥ 12 N/mm²
Rapid strength build-up—50 % after 15 min at 20 °C
Overhead & horizontal installation without sag
HIT-SC sleeves reduce mortar waste by up to 40 %
4. HUS4-CR screw anchorInstallation Guide
Step | Action | Tools/Requirements |
1 | Mark hole | Marker |
2 | Drill & brush | Hammer drill |
3 | Blow dust | Hand pump |
4 | Inject mortar | Dispenser gun |
5 | Insert rod/sleeve | Twist slightly |
6 | Allow cure | 15 min at 20 °C |
5. HUS4-CR screw anchor Application Scenarios
Application | Recommended Spec | Conditions |
Fence posts | M10 × 70 mm + HIT-SC sleeve | Hollow block, wet |
Railing brackets | M8 × 60 mm | Solid brick, indoor |
Bathroom grab bars | M12 × 90 mm | Uncracked concrete |
Air-con supports | M10 × 70 mm | Overhead, 0 °C install |
6. HUS4-CR screw anchor Certifications & Compliance
(1) Conforms to ETAG 001 parts 1 & 5 – solid & hollow masonry
(2) CE-marking – EN 1992-4:2018 & EN 998-2
(3) Service conditions: dry (d/d), wet-use dry (wld), wet-use wet (w/w)
(4) Tested at +5 °C to +40 °C installation temperature
Send Message
