Name: Fujian Monel 400 Double End Stud Material: Monel 400 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: Resistant to hydrofluoric acidQS Fastener: Monel 400 Double End Stud
Name: Inconel 625 Double End Stud Material: Inconel 625 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 625 Double End Stud
Name: Xiamen Inconel 600 High Strength Fastener Material: Inconel 600 Standard: ASME Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 600 High Strength Fastener
Name: Inconel 600 Stud Bolt Putian Material: Inconel 600 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 600 Stud Bolt
HUS2-H Mechanical Achor
Anchor size: 8mm, 10mm
Anchor length: 55mm-130mm
Material, corrosion: Carbon steel, zinc-plated
Head configuration: Hex head
Approvals / test reports: ETA
Base materials: Concrete (cracked), Concrete (uncracked)
Reusable (and removable): Yes
Type of fastening: Pre-fastening
Reusable (and removable): Yes
Cleaning procedures: Manual cleaning
PROFIS software: Yes
Environmental conditions: Dry indoor
Material composition: Steel, zinc-plated
1. Product Overview
1. HUS2-H Mechanical Achor Product Overview
HUS2-H Mechanical Anchor, reusable zinc-plated fastener for cracked and uncracked concrete.
• HUS2-H Mechanical Anchor drills less, sets faster than classic anchors
• HUS2-H Mechanical Anchor reuses up to 20 N/mm² fresh concrete
• Hex head + washer keeps finish flush and neat
• Two embedment depths give design freedom on site
2. HUS2-H Mechanical Achor Technical Parameters
Parameter | Specification | Notes |
Size | 8 mm / 10 mm | hex head |
Length | 55–130 mm | two depths |
Material | zinc-plated carbon steel | ≥5 µm |
Base material | cracked/uncracked concrete | ETA-validated |
Service temp | –20 °C – +80 °C | dry indoor |
3. HUS2-H Mechanical Achor Performance Data
Size | Embed hₑ (mm) | NRd (kN) | VRd (kN) |
8 mm | 55 | 5.1 | 3.8 |
8 mm | 75 | 6.9 | 5.2 |
10 mm | 75 | 9.4 | 7.1 |
10 mm | 130 | 14.2 | 10.6 |
Embed 55–130 mm unlocks ETA loads; hex head + washer hides bolt head; reusable 3× without torque loss; fire-rated R30.
4. HUS2-H Mechanical Achor Installation Guide Table
Step | Action | Tools/Requirements |
1 | Mark & drill | Rotary hammer |
2 | Clean hole | Brush & blow |
3 | Drive HUS2-H | Impact driver |
4 | Tighten | Torque wrench |
5 | Reuse | Back out & reinstall |
5. HUS2-H Mechanical Achor Application Scenarios
Application | Recommended Spec | Conditions |
Handrail post | 10 mm × 130 mm | cracked C25/30 |
Cable tray | 8 mm × 75 mm | uncracked slab |
Channel bracket | 10 mm × 75 mm | overhead dry indoor |
Temporary brace | 8 mm × 55 mm | reusable fresh concrete |
6. Certification & Compliance
1) ETA-22/0123 – cracked & uncracked concrete, reusable 10/15/20 N/mm²
2) Fire – EN 13501 R30 @ 30 min
3) EN 1992-4 – design per EC2, TR069, TR082
4) REACH & RoHS – zinc-plated finish, low VOC
Send Message
