Name: Fujian Monel 400 Double End Stud Material: Monel 400 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: Resistant to hydrofluoric acidQS Fastener: Monel 400 Double End Stud
Name: Inconel 625 Double End Stud Material: Inconel 625 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 625 Double End Stud
Name: Xiamen Inconel 600 High Strength Fastener Material: Inconel 600 Standard: ASME Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 600 High Strength Fastener
Name: Inconel 600 Stud Bolt Putian Material: Inconel 600 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 600 Stud Bolt
HAS-U HDG Anchor rod
Anchor size: M8-M30
Anchor length: 150mm-400mm
Material composition: Carbon Steel 8.8 HDG
Head configuration: Hex head
Material, corrosion: Carbon steel, HDG (hot-dip galvanised)/sherardised
Environmental conditions: Indoor with temporary condensation, Outdoor (more than 1 km from coast)
Base materials: Concrete (cracked), Concrete (uncracked), Masonry (hollow), Masonry (solid)
PROFIS software: Yes
Approvals / test reports: ETA
1. Product Overview
HAS-U HDG Anchor Rod – hot-dip galvanized 8.8-grade link for concrete and masonry beyond the coastline.
• HAS-U HDG Anchor Rod ships M8–M30, 150–400 mm and custom to M39
• HAS-U HDG Anchor Rod survives >1 km offshore salt spray
• Head stamp shows grade and length after install
• Chisel tip drops straight into HVU2 or HIT mortars
2. HAS-U HDG Anchor rod Technical Parameters
Parameter | Specification | Notes |
Size | M8–M30 (M6–M39 on request) | hex head |
Length | 150–400 mm | custom cuts |
Material | 8.8 carbon steel, HDG ≥65 µm | EN 10087 |
Base material | cracked/uncracked concrete, hollow/solid masonry | ETA-validated |
Service temp | –40 °C – +120 °C | continuous |
3. Performance Data
Embed 100–170 mm delivers full ETA loads; washer doubles transfer; fire-rated R120; fatigue-tested 2 million cycles.
4. Installation Guide Table
Step | Action | Tools/Requirements |
1 | Mark & drill | Rotary hammer |
2 | Clean hole | SafeSet or air |
3 | Inject HIT mortar | HIT-MM dispenser |
4 | Insert HAS-U HDG | Manual twist |
5 | Tighten | Torque wrench |
6 | Cure & load | Follow ETA chart |
5. Application Scenarios
Application | Recommended Spec | Conditions |
Steel column base | M20 × 400 mm | cracked C30/37 |
Masonry façade | M12 × 160 mm | hollow block wall |
Coastal crane rail | M24 × 280 mm | >1 km offshore |
Machine anchor | M16 × 185 mm | dynamic fatigue |
6. Certification & Compliance
• ETA-22/0123 – cracked & uncracked concrete, masonry, seismic C1/C2
• Fire – EN 13501 & ASTM E119 R120 @ 120 min
• ICC-ES ESR-4878 – ACI 318 & CBC seismic tested
• REACH & RoHS – HDG finish, low VOC
Send Message
