Recommend Products
Name: Fujian Monel 400 Double End Stud Material: Monel 400 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: Resistant to hydrofluoric acidQS Fastener: Monel 400 Double End Stud
Name: Inconel 625 Double End Stud Material: Inconel 625 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 625 Double End Stud
Name: Xiamen Inconel 600 High Strength Fastener Material: Inconel 600 Standard: ASME Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 600 High Strength Fastener
Name: Inconel 600 Stud Bolt Putian Material: Inconel 600 Standard: ASME B18.2.1 Size: 5/16 to 4 inch Length: 30 to 1000 mm Class: 12.9 Feature: High Yield Strength, Durable Strength and Corrosion ResistanceQS Fastener: Inconel 600 Stud Bolt
Customized Thread Rod China Manufacturer
QS Fastener: Customized Thread Rod China Manufacturer
Name: Customized Thread Rod China Manufacturer
Standard: ASTM
Material: A193 B7
Size: 11-1/8 IN
Total Length: 1200 mm
Surface Treatment: Black
Brand: Qishine
Standard: ASTM
Material: A193 B7
Size: 11-1/8 IN
Total Length: 1200 mm
Surface Treatment: Black
Brand: Qishine
Quantity
As a senior fastener engineer, I can assure you that the Customized Thread Rod from Qishine is more than just a standard bolt—it is a fully tailorable fastening solution engineered to match your specific dimensional, mechanical, and coating requirements. Manufactured from A193 B7 high-strength alloy steel and strictly in accordance with ASTM standards, every piece delivers consistent reliability and long-term durability. To give you a concrete example, we recently supplied a batch of threaded rods with a nominal size of 11-1/8 IN, an overall length of 1200 mm, and a black oxide surface finish. This black coating not only improves corrosion resistance but also provides a uniform, professional appearance. As a dedicated China Manufacturer, we focus on high-precision customization—from special lengths and thread forms to non-standard diameters—so you get exactly what your project demands. Whether you are equipping an industrial processing line or securing critical structural joints in construction, this Customized Thread Rod offers the dependable holding power that engineers trust.
Characteristics and Application Guidance
The Customized Thread Rod is a heat-treated chromium‑molybdenum steel fastener, widely specified for bolting applications involving elevated temperatures, high internal pressures, and cyclic or sustained stresses. To help you select the most suitable configuration for your operating conditions, I provide the following engineering recommendations based on both material science and field practice.
The Customized Thread Rod is a heat-treated chromium‑molybdenum steel fastener, widely specified for bolting applications involving elevated temperatures, high internal pressures, and cyclic or sustained stresses. To help you select the most suitable configuration for your operating conditions, I provide the following engineering recommendations based on both material science and field practice.
1. High‑Temperature Service
This Customized Thread Rod maintains stable mechanical properties across a service range of –29°C to 450°C. However, above ambient temperature, the yield strength of B7 material gradually decreases—a factor that must be accounted for in design.
This Customized Thread Rod maintains stable mechanical properties across a service range of –29°C to 450°C. However, above ambient temperature, the yield strength of B7 material gradually decreases—a factor that must be accounted for in design.
Reference Data (typical values):
- At 300°C, the yield strength retains approximately 90 % of its room‑temperature value.
- At 450°C, the yield strength drops to about 75 % of the room‑temperature value.
- Beyond 500°C, creep and stress relaxation become pronounced; for such cases, I recommend upgrading to a higher‑grade material such as ASTM A193 B16, which offers better high‑temperature stability.
- At 300°C, the yield strength retains approximately 90 % of its room‑temperature value.
- At 450°C, the yield strength drops to about 75 % of the room‑temperature value.
- Beyond 500°C, creep and stress relaxation become pronounced; for such cases, I recommend upgrading to a higher‑grade material such as ASTM A193 B16, which offers better high‑temperature stability.
Selection advice from an engineering perspective:
- If your continuous working temperature approaches 450°C, choose a larger diameter or increase the safety factor to compensate for the reduced strength.
- In environments with frequent thermal cycling, always consider the coefficient of thermal expansion of the threaded rod relative to the mating flanges, and adjust the preload accordingly to avoid gasket crushing or bolt fatigue.
- Schedule periodic re‑torquing or preload verification, especially after the first heat cycle, to counteract relaxation caused by high‑temperature service.
- If your continuous working temperature approaches 450°C, choose a larger diameter or increase the safety factor to compensate for the reduced strength.
- In environments with frequent thermal cycling, always consider the coefficient of thermal expansion of the threaded rod relative to the mating flanges, and adjust the preload accordingly to avoid gasket crushing or bolt fatigue.
- Schedule periodic re‑torquing or preload verification, especially after the first heat cycle, to counteract relaxation caused by high‑temperature service.
2. High‑Pressure Applications
Thanks to its minimum tensile strength of 860 MPa, the Customized Thread Rod excels in high‑pressure bolting scenarios. The allowable working pressure is ultimately governed by the design load, but the table below gives you a quick reference for load capacity at room temperature based on standard metric diameters—data I have validated against ASME and EN calculations.
Thanks to its minimum tensile strength of 860 MPa, the Customized Thread Rod excels in high‑pressure bolting scenarios. The allowable working pressure is ultimately governed by the design load, but the table below gives you a quick reference for load capacity at room temperature based on standard metric diameters—data I have validated against ASME and EN calculations.
| Thread Size | Load Capacity (kN) | Typical Application Guidance |
| M8 | 30 | Light‑duty equipment or low‑load fixtures |
| M10 | 50 | Medium‑load piping supports |
| M12 | 70 | General high‑pressure small flanges |
| M16 | 120 | Higher‑load pressure vessels |
| M20 | 180 | Heavy‑duty connections in compressors |
| M24 | 280 | Large high‑pressure exchangers |
| M30 | 400 | Ultra‑high‑pressure reactors |
| M36 | 560 | Extra‑large equipment or critical turbo‑machinery |
Load capacity calculation:
The values are derived from the formula:
Load Capacity = Tensile Strength (860 MPa) × Tensile Stress Area of the thread.
The values are derived from the formula:
Load Capacity = Tensile Strength (860 MPa) × Tensile Stress Area of the thread.
Safety factor and design check:
- For high‑pressure systems, I strongly advise a safety factor between 1.5 and 2.0, depending on the consequence of failure and the fatigue spectrum.
- Actual design load = Load Capacity ÷ Safety Factor—use this to determine the required diameter and number of rods per joint.
- Always use a calibrated torque wrench or hydraulic tensioner to apply the correct preload, and avoid exceeding 90 % of the material’s proof stress.
- Perform regular in‑service bolt stress checks (e.g., ultrasonic or strain‑gauge methods) to ensure the Customized Thread Rod remains within its elastic range over the equipment life cycle.
- For high‑pressure systems, I strongly advise a safety factor between 1.5 and 2.0, depending on the consequence of failure and the fatigue spectrum.
- Actual design load = Load Capacity ÷ Safety Factor—use this to determine the required diameter and number of rods per joint.
- Always use a calibrated torque wrench or hydraulic tensioner to apply the correct preload, and avoid exceeding 90 % of the material’s proof stress.
- Perform regular in‑service bolt stress checks (e.g., ultrasonic or strain‑gauge methods) to ensure the Customized Thread Rod remains within its elastic range over the equipment life cycle.
Final Word from the Engineer
When you source from a reputable China Manufacturer like Qishine, you gain not only a product made to ASTM A193 B7 but also access to flexible customization—whether you need modified thread lengths, special coatings, or non‑standard diameters up to and beyond 11‑1/8 IN. Our black‑oxide treated rods offer a cost‑effective balance of corrosion protection and aesthetics, while our quality system ensures traceability and dimensional accuracy. For critical projects, I recommend discussing your actual pressure‑temperature curve and bolting torque requirements with our technical team, so we can tailor the Customized Thread Rod precisely to your service conditions. That is the level of engineering support you should expect from a dedicated China Manufacturer—and that is exactly what Qishine delivers.
When you source from a reputable China Manufacturer like Qishine, you gain not only a product made to ASTM A193 B7 but also access to flexible customization—whether you need modified thread lengths, special coatings, or non‑standard diameters up to and beyond 11‑1/8 IN. Our black‑oxide treated rods offer a cost‑effective balance of corrosion protection and aesthetics, while our quality system ensures traceability and dimensional accuracy. For critical projects, I recommend discussing your actual pressure‑temperature curve and bolting torque requirements with our technical team, so we can tailor the Customized Thread Rod precisely to your service conditions. That is the level of engineering support you should expect from a dedicated China Manufacturer—and that is exactly what Qishine delivers.
Send Message
