Hex Plug

QS Pipe Fitting: Xiamen Hex Plug

Hex Plug with a wrench-friendly hex head and NPT threads, sealing openings in fittings and valves in the size and material your line needs.

Quantity

Contact Now

add to cart

One-Minute Overview

Hex head plug for closing openings in fittings and valve bodies.
NPT tapered threads seal by interference as the taper wedges tight.
Carbon steel such as ASTM A105 or stainless grades such as F304L and F316L.
Sizes, ratings and materials are confirmed per inquiry.

A hex plug closes an opening that a fitting or valve body would otherwise leave open, and the hexagonal head is what makes it practical. The flats give a wrench a clean grip for tightening and, just as useful, for removing the plug when a port has to be opened again for maintenance. NPT tapered threads do the sealing by interference, so the thread form and a compatible sealant matter. The plug can be supplied in carbon steel such as ASTM A105 or in stainless grades such as F304L and F316L where corrosion resistance is needed. Because the plug sees full line pressure on its closed face, the rating has to match the system. Sizes, thread forms, materials and ratings are confirmed per inquiry.

Name: Hex Plug
Type: Hex head plug for closing fittings and valves
Thread: NPT, confirmed per inquiry
Material: Carbon steel such as ASTM A105 or stainless grades such as F304L and F316L, confirmed per inquiry
Size and Rating: Confirmed per inquiry
Standard: Confirmed per inquiry
Sizes, thread forms, materials and ratings are confirmed per inquiry, and a detailed specification sheet is available on request.

A hex plug closes an opening that a fitting or valve body would otherwise leave open, and the hexagonal head is what makes it practical. The flats give a wrench a clean grip for tightening and, just as useful, for removing the plug when a port has to be opened again for maintenance. NPT tapered threads do the sealing by interference, so specify the thread form and a compatible sealant, and keep the plug material in step with the body it screws into, whether that is a carbon steel such as ASTM A105 or a stainless grade such as F304L or F316L for corrosive service. Because the plug sees the full line pressure on its closed face, the rating has to match the system. Sizes, thread forms, materials and ratings are confirmed per inquiry.

Fitting a plug is quick but rewards a little discipline. Chase the female thread, check the male taper for damage, apply the sealant the service allows and tighten by the hex, not by the crown, so the wrench does not round the head. Stop when the joint is snug rather than adding another half turn for luck, because over-torque can crack a small body or gall the threads in a fitting you may need to open later. On ports that are stripped regularly, keep a spare plug and note the duty on the order. Sizes and ratings are confirmed per inquiry, so ask for the specification sheet with the order and keep the material certificate with the maintenance records.

FAQ

Q1. What should be fixed before ordering a hex plug?

Four things: the thread form and size of the female port, the pressure rating of the line, the material of the body it screws into, and how often the port will be opened. NPT taper, a matching grade and a compatible sealant give a tight joint; the duty tells you whether a carbon steel or a stainless plug makes more sense.

Q2. Can I just crank it tighter if it seeps a bit?

Resist the urge. NPT seals on the taper, so another half turn usually galls the threads rather than fixing the leak, and on a small body it can start a crack. Back it out, clean both flanks, recheck the sealant and tighten by the hex to a snug joint. If it still weeps, the threads are worn, not loose.

Q3. Is the hex head there just to look official?

It is there so the plug comes back out. A rounded head and a seized thread turn a five-minute inspection into a drill-and-tap job, and the flats are what stop that. They also keep the wrench off the tapered flanks, so the sealing surface arrives at the port in one piece.

Q4. What's the minimum I can order?

Standard flange insulation gasket kits start at one set, and standard gaskets, studs, washers and sleeves start at one piece. Kits made to your drawing or for a non-standard bolt pattern are quoted individually, because the minimum really depends on the material and the tooling involved.

Send Message