CS Q235 Concentric Reducer

QS Pipe Fitting: Suzhou CS Q235 Concentric Reducer

A Q235 carbon steel concentric reducer with butt weld ends that steps the line down while keeping the centerline aligned.

Quantity

Contact Now

add to cart

One-Minute Overview

A Q235 carbon steel concentric reducer for butt weld pipelines.
2 x 1 inch, keeping the pipe centerline aligned.
Standard wall with bevelled ends for a full penetration weld.
Sizes, schedules and grades are confirmed per inquiry.

A concentric reducer steps a pipeline from one diameter to another while keeping both ends on the same centerline. That symmetry is exactly why it is chosen for vertical pump suction lines and horizontal transitions where an even flow distribution matters and where an offset flat side would collect vapour or sediment. This one is made from Q235 carbon steel to ASME B16.9 dimensions, in a 2 x 1 inch size with standard wall and bevelled butt weld ends. The full penetration welded joint matches the strength of the connecting pipe and gives a smooth internal transition that limits turbulence and pressure drop. It is a standard fitting on petroleum pipeline work, shipped in veneer cases or on pallets.

Name: CS Q235 Concentric Reducer
Material: Q235
Type: Concentric
Standard: ASME B16.9
Size: 2 x 1 Inch
Thickness: STD
End: Butt Weld
Feature: Corrosion Resistance
Usage: Petroleum Pipeline
Packing: Veneer Case or Pallet
Sizes in inches, wall schedules and end preparation are confirmed per inquiry, and a detailed specification sheet is available on request.

Selection starts with the two diameters and the reason for the reduction. Confirm the large and small end sizes, the schedule on each, and whether the line is a pump suction, where keeping the centerline is critical to avoid an air pocket, or a horizontal transition, where an eccentric reducer might actually be the better call. Match the Q235 grade and the standard wall to the design pressure and the corrosion allowance, and check the ASME B16.9 face to face length so the reducer fits the spool without trimming. Where corrosion is a concern, the natural oxide layer can be backed with anti rust oil or a coating. Sizes, schedules and grades are confirmed per inquiry against the isometric. Every size, wall schedule and end type is confirmed per inquiry against the spool drawing.

Welding a reducer is about a smooth bore on both ends. Verify the bevels on the large and small ends, keep the two pipes and the reducer on one centerline, and hold the root gap evenly before tacking. Use a filler and procedure qualified for Q235 and control the heat input on the smaller end so the root does not protrude into the bore. After welding, inspect the bead and the internal transition, and add radiographic or ultrasonic examination where the design code asks. Cap both ends in transit, store the reducer dry, and confirm the size marking before it goes into the spool so the 2 inch end lands on the correct side of the pump.

FAQ

Q1. When should I use a concentric reducer and when an eccentric one?

It depends on what the line is carrying and where it sits. A concentric reducer keeps the centerline, so it suits vertical runs and pump suction where you want an even, symmetric flow. On a horizontal line carrying liquid with vapour, or where a flat top or bottom avoids a pocket, an eccentric reducer is usually chosen instead. Tell us the orientation and the service with the inquiry and the right type can be confirmed.

Q2. Does the wall really have to match the pipe on both ends?

Yes. If the reducer wall is heavier or lighter than the pipe on either end, the internal step disturbs the flow and the weld has to bridge a mismatch. Order the same schedule on both the large and small ends, confirm both bevels, and the fitter can tack square without grinding the bore back. It is especially important on a pump suction, where a step at the joint can disturb the flow enough to bother the pump.

Q3. Can I install it either way round in a horizontal line?

You can physically weld it either way, but that does not make it right. A concentric reducer is symmetric about its axis, yet the direction of flow and the reason for the size change are not, and the face to face length and the bevels are cut for a defined large and small end. Put the large end on the upstream side the isometric calls for, check the size stamping, and you will not discover the mistake at the pump flange.

Q4. What payment terms do you accept?

T/T, L/C at sight and other internationally accepted terms. The exact terms are agreed with you before production starts, because the payment schedule has to match the order value, the shipping method and the delivery schedule you need — which is also why we confirm them up front rather than after shipment.

Send Message