Concentric Reducer

QS Pipe Fitting: Fujian Concentric Reducer

Concentric Reducer in sizes 1/2 to 80 Inch and walls SCH5 to SCH160, supplied in four steel grades to ANSI, ISO, JIS and DIN standards.

Quantity

Contact Now

add to cart

One-Minute Overview

Concentric reducer joining 1/2 to 80 Inch pipe while keeping the flow centerline.
Walls from SCH5 to SCH160 to match pressure and corrosion allowance.
Carbon, stainless, alloy and duplex steel for different media.
Made to ANSI, ISO, JIS and DIN manufacturing standards.

A concentric reducer connects pipes of different diameters while keeping the centreline of the flow in one straight line. The two ends sit on the same axis, so the transition from the large bore to the small bore is symmetrical and the fluid is guided evenly rather than thrown against one side of the wall. That is what keeps turbulence and pressure loss low, which matters on pump discharges, in chemical processing lines carrying hazardous fluids, and anywhere a sudden disturbance could grow into a leak or a vibration problem. Sizes here run from 1/2 to 80 Inch with walls from SCH5 to SCH160, in carbon steel, stainless steel, alloy steel and duplex steel, manufactured to ANSI, ISO, JIS and DIN standards.

Name: Concentric Reducer
Type: Concentric, same-axis diameter transition
Size: 1/2-80 Inch
Wall Thickness: SCH5-SCH160
Material: Carbon Steel, Stainless Steel, Alloy Steel, Duplex Steel
Manufacturing Standards: ANSI, ISO, JIS, DIN
Sizes, wall thicknesses and schedules are confirmed per inquiry, and a detailed specification sheet is available on request.

Choose the reducer by the geometry first. Because both ends share an axis, a concentric reducer keeps the pipe centreline where it was, which is the right answer on vertical runs and on pump discharges where you want an even approach to the impeller. It is also the usual choice on lines carrying hazardous chemicals in process plants, since a smooth, symmetric transition cuts turbulence and the pressure loss that comes with it. Where a horizontal line has to drain completely or avoid an air pocket at the top, an eccentric reducer with one flat side is the better tool; pick that consciously instead of defaulting to concentric everywhere. Then select the wall from SCH5 to SCH160 against design pressure and corrosion allowance.

Material follows the fluid and the standards follow the plant. Carbon steel covers general oil, gas, water and utility duty, stainless steel handles corrosive or clean media, alloy steel suits hotter service, and duplex steel brings strength and corrosion resistance together for demanding chemical or chloride environments. Because the reducer is made to ANSI, ISO, JIS or DIN practice, confirm which dimensional series the existing pipework uses before ordering, so the two bevels match the mating pipe. Installation is a butt weld: bevel both ends, keep the reducer square to the run, and hold an even root gap so the small end does not drift off centre as the joint cools. Inspect the bead and bore, and keep the transition free of weld spatter that would disturb the smooth flow you bought it for.

FAQ

Q1. When is a concentric reducer the correct geometry?

When the two pipes should share a centreline. A concentric reducer gives a symmetric, gradual transition that guides the fluid evenly, keeping turbulence and pressure loss low on vertical runs, pump discharges and process lines carrying hazardous chemicals. If a horizontal line instead needs full drainage or has to avoid a trapped gas pocket, an eccentric reducer with one flat side is the deliberate alternative, not an afterthought.

Q2. Four steels again - which one do I actually pick?

Follow the fluid, then the rest of the line. Carbon steel is the everyday choice for oil, gas, water and utilities; stainless when the medium corrodes iron or cleanliness matters; alloy when the temperature climbs; and duplex when you need strength plus chloride resistance in chemical duty. Match the grade to the adjoining pipe so the weld joins compatible metals and the corrosion allowance is the same on both sides of the joint.

Q3. Does the 1/2 to 80 Inch range mean I can order a funnel-shaped one?

It means the range is wide, not that the shape changes. From a small instrument line up to a large header, the reducer stays a concentric, same-axis transition with ends sized to the two pipes it joins. Confirm the exact large and small diameters, the wall schedule from SCH5 to SCH160, and the standard series on your inquiry, so the bevels land on the right pipe and the fit-up does not need a field fix.

Q4. What's the minimum I can order?

Standard flange insulation gasket kits start at one set, and standard gaskets, studs, washers and sleeves start at one piece. Kits made to your drawing or for a non-standard bolt pattern are quoted individually, because the minimum really depends on the material and the tooling involved.

Send Message