ASTM A312 TP304 Pipe

QS Pipe: Xiamen ASTM TP304 Pipes

ASTM A312 TP304 welded pipe, 4 inch and 2 mm wall in 6 m plain end lengths for main runs on petroleum and chemical piping.

Quantity

Contact Now

add to cart

One-Minute Overview

ASTM A312 TP304 welded pipe in 4 inch size with 2 mm wall and 6 m lengths.
Plain ends for butt welding into a main run or a long refinery spool.
Austenitic 304 keeps petroleum and chemical lines free of rust and scale.
Every length hydrostatically tested, with the weld seam examined before dispatch.

This TP304 pipe is the 4 inch workhorse of an A312 stainless line: welded construction, 2 mm wall, plain ends, 6 m lengths with protective caps. Four inch is where a branch line becomes a real run — it carries product between units rather than feeding one instrument — and the smooth interior of a welded austenitic pipe keeps flow steady across the length. Made to ASTM A312, the pipe arrives with defined chemistry, wall tolerance and testing, so it drops into a petroleum pipeline specification without a debate about what the mill actually supplied.

Name: ASTM A312 TP304 Pipe
Type: Welded
Size: 4 Inch
Material: SS 304
Standard: ASTM A312
End: Plain
Thickness: 2 mm
Length: 6 m
Feature: Corrosion Resistance

Selecting this pipe is mostly about matching service to grade. TP304 covers water, oil, refined product and mildly corrosive chemicals; it resists the rust and pitting that cut carbon steel life short in wet service. The weld seam follows the same acceptance route as the rest of A312 pipe: hydrostatic test on every length and non-destructive examination where the line specification calls for it. At 4 inch, fit-up matters — square cuts, a consistent root gap and a controlled heat input keep the weld from pulling the run out of line over six metres of pipe.

Handling and installation decide how the pipe performs after it leaves the mill. Keep the end caps on during transport so plain ends stay clean and round, store the bundles supported and out of standing water, and keep carbon steel tooling away from the stainless surface to avoid iron contamination. Weld with a matching 304 consumable and avoid excessive interpass heat, which can sensitise the heat affected zone in a heavily welded spool. Size and wall thickness are confirmed per inquiry, and a detailed specification sheet is available on request.

FAQ

Q1. What does plain end mean when I am welding a 4 inch run?

Plain end means the pipe is cut square with no bevel machined into it, so you prepare the weld edge on site. Deburr, cut the bevel to your welding procedure, and keep the root gap consistent across the joint. Plain ends also make it easy to trim the 6 m stock length to fit a spool drawing without ordering a special end preparation.

Q2. How do I keep the weld from sensitising the 304?

Sensitisation is carbide precipitation in the heat affected zone after slow cooling through the critical range. Control it with moderate heat input, fast travel and low interpass temperature rather than cooking the joint. In ordinary petroleum service the effect is small, but if the line will be welded heavily and then exposed to strong acids, specify a low-carbon grade instead.

Q3. Can this pipe take a flanged connection instead of a butt weld?

Yes. Fit a weld neck or slip-on flange to the plain end with a full penetration butt weld, and the joint behaves like any other flanged point on the line. Just keep the flange face protected during welding so the gasket surface is not spattered, and verify alignment before the root pass — a flange welded on a twisted pipe is an argument nobody wants.

Q4. How long will production take for these TP304 pipes?

Standard sizes are typically ready within 30 days, and in-stock items ship immediately. Larger or custom orders get a confirmed date per order, because the schedule depends on quantity, material, the bolt pattern you specify, and how busy production is at the moment you order.

Send Message