A234 Wpb Reducer

QS Pipe Fitting: Jiangsu A234 WPB Reducer

A234 WPB Reducer in eccentric or concentric form, STD wall and butt weld ends to ASME B16.9, for flow control in petroleum pipelines.

Quantity

Contact Now

add to cart

One-Minute Overview

A234 WPB reducer to ASME B16.9, in eccentric or concentric form.
STD wall and butt weld ends for a secure, leak-proof joint.
Corrosion resistance for demanding petroleum pipeline duty.
Packed in veneer case or pallet for safe delivery.

The A234 WPB Reducer is the fitting that changes pipe diameter in a petroleum pipeline without disturbing the flow more than it has to. Made from A234 material and built to ASME B16.9, it is available in both eccentric and concentric types: the concentric version keeps the two ends on one centreline, while the eccentric version holds one side flat so a horizontal line can drain or avoid a gas pocket. Standard thickness and butt weld ends give a secure, leak-proof connection, and the corrosion resistance feature is aimed at the harsh conditions these lines see in service. Each unit is packed in a veneer case or on a pallet so it arrives ready for the spool shop.

Name: A234 WPB Reducer
Material: A234
Standard: ASME B16.9
Type: Eccentric / Concentric
Thickness: STD
End: Butt Weld
Feature: Corrosion Resistance
Usage: Petroleum Pipeline
Packing: Veneer Case or Pallet
Sizes, wall thicknesses and types are confirmed per inquiry, and a detailed specification sheet is available on request.

The choice between eccentric and concentric is the first one to settle, and it is a layout question. On a vertical line or a pump discharge where you want an even, symmetric approach, the concentric reducer keeps the centreline straight and the transition smooth. On a horizontal run, the eccentric reducer is often the safer answer: installed with the flat side down it lets the line drain completely, and with the flat side up it prevents a gas pocket forming before a pump suction. Get that orientation onto the spool drawing, because rotating the fitting in the field after the fact defeats its purpose. Then match the STD wall to the adjoining pipe and confirm the ASME B16.9 dimensional series so the two bevels meet cleanly. The A234 material is the standard butt weld fitting grade for this petroleum service.

Installation is a butt weld, so treat it like any other welding fitting. Bevel both ends to the joint design, hold an even root gap, and align the reducer square to the run so the small end does not drift off axis as the joint cools. With an eccentric reducer, double-check the flat side is where the drawing says before tacking - it is the one detail that is easy to lose in a busy fabrication shop. Weld with a procedure qualified for the material and wall, keep the bore free of spatter, and inspect the bead and the internal transition. Because the product is described with corrosion resistance for harsh petroleum conditions, protect the coating or surface during handling and storage, and keep the veneer case or pallet intact until the fitting reaches the workface. Confirm sizes, thickness and type on the inquiry.

FAQ

Q1. How do I choose between the eccentric and concentric type?

From the layout, not from habit. A concentric reducer keeps the centreline straight and suits vertical runs and pump discharges where an even approach matters. An eccentric reducer holds one side flat, so on a horizontal line flat-side-down gives complete drainage and flat-side-up avoids a gas pocket before a pump suction. Put the orientation on the spool drawing, because turning the fitting later defeats the reason you chose it.

Q2. What does STD wall mean for my order?

It means the reducer comes in standard wall thickness rather than a heavier schedule, which suits plenty of general petroleum pipeline duty. The important part is that it matches the pipe it welds to: a lighter reducer in a heavier line becomes the thin point, and a heavier one wastes material and welding time. Check the adjoining pipe schedule against the ASME B16.9 series and confirm the thickness on the inquiry.

Q3. Any way to mess up an eccentric reducer on site?

Easily: weld it in with the flat side on the wrong side. The whole point of an eccentric reducer is that one face stays level, so flat-side-down drains a horizontal line and flat-side-up keeps gas off a pump suction. Once tacked and welded, rotating it is not an option. Check the orientation against the spool drawing before the first tack, keep the root gap even, and you will not be explaining a persistent air lock later.

Q4. What's the minimum I can order?

Standard flange insulation gasket kits start at one set, and standard gaskets, studs, washers and sleeves start at one piece. Kits made to your drawing or for a non-standard bolt pattern are quoted individually, because the minimum really depends on the material and the tooling involved.

Send Message